Within a few years of decoration, some floor tiles and wall tiles in the home were warped, affecting normal life. In this case, we must first find out the reason. The following is the reason why the ceramic tiles I carefully arranged for you rise. Let's have a look.
I. the expansion gap reserved between the floor tile and the walls around the floor tile is too narrow! When the room temperature changes violently, the floor, cement layer and ceramic tile will expand and contract with heat. If the gap is too thin and there is not enough space for the ceramic tile to "stretch", the ceramic tile is easy to arch, which is easy to occur in the north and not easy to occur in the South because of large humidity and small temperature difference.
II. When paving floor tiles, cement and yellow sand were not mixed in the correct proportion. If the cement grade is low and the yellow sand is put more, over time, the cement in the lower layer will not be able to adhere to the floor tile, causing the floor tile to tilt up.
III. If the original cement floor is very smooth and the floor tiles are paved without roughening, it is also easy to have the phenomenon of floor tile arching.
Solution of ceramic tile warping
If the ceramic tile falls off and there is loose "delamination" between the cement mortar layer under the ceramic tile and the wall base or ground base, the cement mortar layer on the wall can be cleaned with tools such as a shovel, and the ceramic tile can be paved after reapplying the cement mortar.
I. remove all the upturned bricks, and then clean the bottom of the bricks, level them with cement, and then put the bricks on them.
II. Find a cutting machine to cut the seam of the upturned floor. Pay attention to cutting the just upturned floor. Otherwise, if there is no hair cutting, lift up the upturned floor, sweep it below, and apply floor glue on each floor and stick it on.
III. the floor cocks up and bursts. Generally, it occurs in severe cold or hot summer when the temperature changes sharply. The direct reason is that the floor tiles and other building materials squeeze and collide with each other due to thermal expansion and cold contraction, which is mostly caused by improper decoration construction and the quality of building materials. Experts suggest that the laying of floor tiles should pay attention to the use of cement above 425 for laying floor tiles. The sand should be filtered and dripping coarse sand, with a ratio of 1:2, and a 1mm expansion joint should be reserved.
1. Maintenance method of polished brick
Try to avoid metal objects or hard objects such as sand directly or frequently rubbing the surface of Microcrystalline stone, and carpet can be paved; Do not contact with corrosive substances such as strong acid for a long time; Clean the contaminated surface with clean water, alkaline cleaner or organic solvent frequently; It is recommended to place soft carpets and soft soled cloth slippers at the indoor door; A variety of cleaners on the market contain hydrofluoric acid (HF) and hard particles, which are easy to damage the surface of ceramic tiles, so they should be avoided as far as possible; Regular waxing or mirror treatment is recommended.
2. Antique bricks shall be cleaned along the texture
The surface of antique brick has concave convex texture to pursue the realistic effect of log. It can be cleaned along the texture. If tea or other daily necessities are attached to the surface of ceramic tiles, they can be cleaned with household detergent and clean water along the texture to make the ceramic tiles more shiny.
3. Cleaning of glazed tile joints
The cleaning of glazed tiles is relatively simple, but it is easy to hide dirt at the joints of ceramic tiles. First use a toothbrush dipped in a little decontamination cream to remove dirt, and then brush a layer of waterproof agent with a brush at the gap, which can not only prevent water seepage, but also prevent mold growth.
4. Use detergent for stubborn stains on ceramic tiles
In addition to the daily sweeping and mopping of the floor tiles, we can use multi-functional detergent to regularly clean and maintain the stubborn stains at the gaps and corners of the tiles, so as to keep the tiles clean and bright.
5. Skillfully use toothpaste at the joints of ceramic tiles
The main raw materials at the joints of ceramic tiles are putty and white cement. It is difficult to scrub the oil stain after it is adhered to it. Choosing toothpaste with strong cleaning effect can also clean the stain. For the ceramic tile joint at the kitchen stove, after cleaning, you can drip candles to prevent oil pollution.
6. Apply waterproof agent to ceramic tile scratches
Toothpaste is a big help for ceramic tile scratches. A small scratch was accidentally left on the smooth and flawless ceramic tile, which made everyone very distressed. At this time, we can smear toothpaste on the scratch and wipe it with a rag to repair it. The gap between bricks can be removed from time to time with decontamination cream, and then brush a layer of waterproof agent on the gap to prevent mold growth.
7. Debris shall be removed during tile renovation
To renovate the old ceramic tile, it should be noted that the whole ceramic tile should be removed, and then the new ceramic tile should be replaced. The color number of the new ceramic tile must be consistent with the original one, otherwise there will be color difference, so it is suggested to leave a small amount of ceramic tile during decoration and tiling for repair in the future. If you don't keep it, you'd better take the broken tiles to the specialty store for replenishment.
I. remove all the upturned bricks, and then clean the bottom of the bricks, level them with cement, and then put the bricks on them.
II. Find a cutting machine to cut the seam of the upturned floor. Pay attention to cutting the just upturned floor. Otherwise, if there is no hair cutting, lift up the upturned floor, sweep it below, and apply floor glue on each floor and stick it on.
III. the floor cocks up and bursts. Generally, it occurs in severe cold or hot summer when the temperature changes sharply. The direct reason is that the floor tiles and other building materials squeeze and collide with each other due to thermal expansion and cold contraction, which is mostly caused by improper decoration construction and the quality of building materials. Experts suggest that the laying of floor tiles should pay attention to the use of cement above 425 for laying floor tiles. The sand should be filtered and dripping coarse sand, with a ratio of 1:2, and a 1mm expansion joint should be reserved.
Guess you're interested:
1. What are the causes of ceramic tile collapse
2. What is the reason for the ceramic tile infiltrating into the stain and how to do it
3. What is the reason for the flat middle arch at the four corners of the ceramic tile and how to do it
4. What is the reason for the rise of ceramic tiles
5. What is the reason for the middle arch of ceramic tile and how to do it