Now more and more people use Leike router. It is found that many novices ask Leike wireless router how to set the password. In fact, it is very simple. Just enter the router setting interface and set it. Now I will introduce the method in detail for you. You are welcome to refer to and learn.
Specific setting methods and steps:
1. Enter 192.168.1.1 in the browser address, then press enter to confirm and enter the login account password. The login account password of Leike is guest by default. After entering, you can enter the setting interface of Leike wireless router. (you can view the login account information on the back of the router.)
2. Leike now has a quick configuration function, which greatly simplifies the setting steps. As shown in the figure below, click quick configuration. Even if the router is set for the first time, it can be set in this interface at one time.
WAN port setting: the WAN port link type defaults to PPPoE mode. The internet account password is the broadband account given to you by the operator. Fill it in and it's OK.
The wireless internet account password is set in the following wireless configuration settings: the wireless status is turned on, and the SSID number is the wireless connection account, which can be filled in by yourself. Security settings - password. Fill in the password is the password for wireless connection.
The security mode is wpa-psk / wpa2-psk AES encryption by default.
Click Save to take effect, so that the wireless password setting is good.
Note: if your Leike router version does not have this quick setting function, it can be set in wireless management - wireless security management, which is the same.
3. Generally, the DHCP service is enabled by default and the IP address is automatically assigned. Otherwise, you have to fill in the IP address manually when surfing the Internet, which is more troublesome.
Conclusion: the setting of Leike wireless router is still relatively simple. I believe novices should immediately say that it was so simple after reading this graphic tutorial. They felt it was difficult before doing it. Other router settings are similar, which are relatively simple. Now it's becoming more and more stupid. Generally, you only need to fill in the account and password, and others don't need you to move by default.
Finally, we summarize the detailed setting steps of Leike wireless router
Leike wireless router setting method and steps:
1、 Installation of Leike wireless router
The first is to install Leike wireless router, which is mainly to connect the cat, Leike wireless router and computer with network cable. We have introduced the router connection before. The installation and connection diagram of wireless router is as follows:
First of all, if the network cable is similar to the telephone line, it is generally necessary to connect the network cable pulled back from the outside to the cat, then connect it to the wireless router from the other end of the cat, and finally connect the wireless router to the computer (this is the most common connection method of broadband in our family). In fact, the installation of wireless router is quite simple, as shown in the following figure:
Schematic diagram of network cable connection between cat, router and computer
For some cell broadband, there is no need to connect the cat. You can directly connect the router. The installation method is as follows:
How to install a wireless router
As like as two peas, the router is installed after the router has finished the connection, but we need to enter the computer to set up a wireless router before it can be used. Then how do we set up the Netcore wireless router? Here we will introduce, the installation of Netcore wireless router is exactly the same as other wireless router installation.
2、 Leike wireless router settings
1. After the installation of Leike wireless router is completed, we open the computer, then open IE browser, enter 192.168.1.1 in the browser address, and then press enter to enter the setting interface of Leike wireless router, as shown in the following figure:
Enter the setting interface of Leike wireless router
2. After that, the login dialog box of Leike wireless router will pop up. The default login account name and password of Leike wireless router are lowercase guest, which is different from that of many other wireless routers. Novice friends should pay special attention to this. They can't log in to the internal settings of Leike wireless router, as shown in the following figure:
Leike wireless router login interface
3. As shown in the figure above, after entering the user name and password, click OK to open the setting interface of Leike wireless router. All settings, including internet account and wireless settings, will be set in the following interface, as shown in the figure below:
Leike wireless router setting interface
4. Set router parameters. First, enter the WAN setting page. There is a wizard button in the upper right corner of each page. First, click "Wizard" to set the router. After entering the setting wizard, we click next. The first step is wan setting. The main function here is to fill in the internet account and password provided by the network provider.
In Wan settings, the router provides three connection modes, including dynamic IP users, PPPoE users and static IP users. We can choose according to our actual situation. We need to enter different parameters to choose different methods. Usually, we use dial-up Internet access, that is, PPPoE users. If you don't know your Internet type, you can call Leike service hotline or ask the local broadband operator. The main differences among the three are:
Choose your Internet access method
PPPoE users (ADSL): applicable to most users of China Telecom and China Netcom. Most of these users have a modem and need an account and password to access the Internet.
Cable modem: it is generally used for community broadband. In the past, the computer was powered on to access the Internet, and the network configuration was "automatically obtain the IP address".
Static IP users: computers are users who surf the Internet through designated IP addresses. Previous computers were configured with fixed IP addresses.
Method 1: our most common way to access the Internet PPPoE users: fill in the account and password, and all other settings remain unchanged. Directly click "save and take effect" and wait for 1 minute before accessing the Internet. As shown below:
The most common PPPoE online setting method
If you access the Internet through dynamic IP user mode, select this option first, and then set DHCP client parameters. First enter the MCA address of the router. If you don't know the exact MAC address, you can click the MAC address clone button to get it. Or click the restore default MAC button to use the default address. Finally, enter MTU and master-slave DNS parameters and click Apply (this is rarely used by ordinary home users).
Dynamic IP user settings
Method 2: as shown in the figure above, dynamic IP user: select "cable modem" and click "save and take effect" without changing anything else.
Static IP user setting method
Method 3: if it is a static IP user: select the "static IP user" user, and fill all the original blank options into your parameters as shown in the figure. If you do not know the of each fixed parameter, please contact the network administrator.
PS: the Internet access mode of general household users is PPPoE user mode, mode 2 and mode 3. General users rarely use mode 1. Mode 1 is the network cable pulled by families from network providers such as telecom and Netcom; Mode 2 is community broadband, and mode 3 is usually corporate network. Therefore, you can only look at mode 1, mode 2 and mode 3.
5. After the above is completed, we will enter the wireless setting. First, click the "wireless management" option on the left of the main page to set the basic wireless setting. All we need to do is turn on the wireless function, enter the wireless network name (you can fill in it arbitrarily) and select the channel, as shown in the following figure:
Basic settings of Leike wireless router
6. Then select "WPA2" encryption type in the encryption type under the "security management" tab, and enter the wireless password we set below, as shown in the following figure:
Setting method of Leike wireless router
As shown in the figure above, Leike wireless router supports setting multiple wireless login passwords. Usually, you need to set a few. Then click finish at the bottom.
Note: 802.11n standard stipulates that the nominal transmission rate of the router can be reached only by selecting wpa-psk-aes or wpa2-psk-aes encryption mode. Leike wireless router strictly follows international standards and also needs such encryption to reach 150m or 300m. Wpa2-psk-aes encryption method is the best choice, because the wireless network of this wireless encryption method is the most difficult to be released by others.
The latter access control and WDS do not need to be set, unless it is really necessary to control the network or access. The function of WDS is to enhance the transmission distance of the wireless network. Generally, it can be set by default, and there is no need to set. After the above settings are completed, remember to save them. After the setting of Leike wireless router is basically completed, we can start to surf the Internet and use the wireless Internet.
The above is the basic configuration tutorial of Leike wireless router shared by Xiaobian. As for the advanced configuration, you can understand it after you are familiar with these basic. It is not introduced in detail here, because the above introduction has completed all the settings of Internet access and can access the Internet with normal wireless router. Here, it is recommended that you like to play with the advanced settings. Once the settings are wrong and you can't access the Internet, you can restore the router to the factory configuration, and then access the Internet again according to the above basic settings.